MC-SVP (MCSVP, MC SVP)
MC-SVP is intended to check the inertia braking system of trailers vehicle categories O2 and O3.
Product Specifications MC-SVP:
A range of efforts in pushing the trailer coupling device - from 0kN to 5kN;
Operating pressure generated in the pneumo-mechanical block device MC-SVP - 0.5 MPa, 0, 8MPa;
Unit price of the least bit CPU - 0.1 N;
Maximum permissible relative error of the creation and measurement efforts in pushing the trailer coupling device - ± 1%;
Degree of protection against dust and moisture - IP54;
Electrical power electronic module unit MC-SVP performed on eight batteries;
Pushing the inertial force of the trailer creates a pneumatic cylinder Drome.The measurement is performed pushing efforts of the resistance strain gauges, electronic sensor efforts;
Pushing force between the car-tractor and trailer passed through in the standard towbar.Creating a force is pushing through a built-ton cylinder which is applied to the input air pressure.Measurement of the push to efforts made electronically strain gage force, the report of the current and the peak value of the measured values of the efforts carried out through a digital-indicating device (CPU) of the electronic device unit MC-SVP, which is connected via cable to the sensor efforts.Wheels of the trailer during the measurement should be located on the roller brake tester. Fear of the nal circuit prevents movement of the trailer.Thus the wheels of the trailer kept on the rolls;
Make sure to test the tire pressure trailer, the inertial force of the pressure in the tractor trailer, the pressure must match the value specified in the instructions on the trailer;
Install a trailer on a roller brake tester in accordance with the instructions and place the towbar so that it can be easily draw hydraulic jack;
Disconnect the car-truck from the trailer and move the MC-SVP for towing a trailer hitch.Raise the hydraulic jack to top the ball went into the device towbar trailer;
Set the height of the ball unit so that the unit and tow bar are parallel to the trailer and fasten the device to the roller chain clamp around thee govo coupling the trailer.To adjust the height of the ball, rotate the disk;
After that, fasten the chain connecting the device, so that is not created during the work interfere with moving parts of the trailer brake tester and the device;
Lower the jack and hang the trailer with the device installed on the MC-SVP trailer hitch of the tractor vehicle;
Connect the compressed air through a flexible hose to the input of the pneumatic cylinder and an electronic unit to the sensor efforts. Check the set pressure on the regulator. Yes sisting must be equal to 6 bars;
To prevent the expulsion of the trailer brake tester rollers, put the vehicle on the parking brake;
To increase or decrease given by the pushing force, it is necessary to help feed the pressure regulator to increase or decrease the value of the supplied air pressure;
Monitor the pushing force given by using an electronic device unit;
After starting the roller brake tester slowly increase the pressure (given by the pushing force) to block the wheels of the trailer or the maximum effort, designed for the mass of the trailer;
Turn off the bench, move the control lever of pressure to "lock feed pressure" and make sure that the display of the current efforts to push the CPU of the electronic unit is equal to zero;
To remove the device MC-SVP - an operation inverse to the preparation of the measurements;
Connect the trailer to the car-tractor (important parameter of the inertial force of the pressure on the tractor trailer).Check that it is capable of safe passage, and going away from the brake stand;
The manufacturer guarantees the quality of the product MC-SVP technical requirements specifications, subject to the consumer the terms and conditions of storage, transportation, installation, operation, established specifications and operational documentation.
|Sales departments LLC "Zapadpribor"
|1008 RUB||in stock:||4195 RUB||in stock:|
|370 UAH||5781 pieces||1145 UAH||20 pieces|
|1328 RUB||in stock:||4195 RUB||in stock:|
|487 UAH||2640 pieces||1145 UAH||23 pieces|
|1014 RUB||in stock:||5000 RUB||in stock:|
|372 UAH||2784 pieces||1250 UAH||15 pieces|
|2213 RUB||in stock:||5680 RUB||in stock:|
|487 UAH||1635 pieces||1420 UAH||18 pieces|
|1109 RUB||in stock:||5380 RUB||in stock:|
|394 UAH||3143 pieces||1345 UAH||21 pieces|
Built-in printer and a keyboard, memory, transfer data to a computer
Wheatstone bridge, resistance box measure, the resistance coils:
Attention! Delivery of all instruments, which are listed on the site, is on the whole territory of the following countries: Russia, Ukraine, Belarus, Kazakhstan and other CIS countries.
According to Russia, there is an established system of delivery to cities: Moscow, St. Petersburg, Surgut, Nizhnevartovsk, Omsk, Perm, Ufa, Norilsk, Chelyabinsk, Novokuznetsk, Cherepovets, Almetyevsk, Volgograd, Lipetsk, Magnitogorsk, Togliatti, Kogalym Kstovo New Urengoy Nizhnekamsk, Nefteyugansk, Nizhny Tagil, Khanty-Mansiysk, Yekaterinburg, Samara, Kaliningrad, Nadym, Noyabrsk, Vyksa, Nizhny Novgorod, Kaluga, Novosibirsk, Rostov-on-Don, Upper Pyshma, Krasnoyarsk, Kazan, Naberezhnye Chelny, Murmansk, Vsevolozhsk Yaroslavl, Kemerovo, Ryazan, Saratov, Tula, Usinsk, Orenburg, Novotroitsk, Krasnodar, Ulyanovsk, Izhevsk, Irkutsk, Tyumen, Voronezh, Cheboksary, Neftekamsk, Novgorod, Tver, Astrakhan, Novomoskovsk, Tomsk, Prokopyevsk, Penza, Urai, Pervouralsk , Belgorod, Kursk, Taganrog, Vladimir, Neftegorsk, Kirov, Bryansk, Smolensk, Saransk, Ulan-Ude, Vladivostok, Vorkuta, Podolsk, Krasnogorsk, Novouralsk, Novorossiysk, Khabarovsk, Zheleznogorsk, Kostroma, Zelenogorsk, Tambov, Stavropol, Svetogorsk, Zhigulevsk , Arkhangelsk and other cities of the Russian Federation.
Ukraine has a well-established on the delivery system in the cities: Kiev, Kharkov, Dnepr (Dnepropetrovsk), Odessa, Donetsk, Lviv, Kiev, Nikolaev, Lugansk, Vinnitsa, Simferopol, Kherson, Poltava, Chernihiv, Cherkasy, Sumy, Zhytomyr, Kirovohrad, Khmelnytsky, Rivne, Chernivtsi, Ternopil, Ivano-Frankivsk, Lutsk, Uzhgorod and other cities of Ukraine.
On Belarus there organized system of delivery to cities: Minsk, Vitebsk, Mogilev, Gomel, Mozyr, Brest, Lida, Pinsk, Orsha, Polotsk, Grodno, Zhodino Molodechno and other cities of Belarus.
In Kazakhstan there is an established system of delivery to cities of Astana, Almaty, Ekibastuz, Pavlodar, Aktobe, Karaganda, Uralsk, Aktau, Atyrau, Arkalyk, Balkhash, Zhezkazgan Kokshetau Kostanai, Taraz, Shymkent, Kyzylorda, Lisakovsk, Shakhtinsk, Petropavlovsk, reader, Ore, Families, Taldykorgan, Temirtau, Ust-Kamenogorsk and other cities of Kazakhstan.
Ongoing delivery of devices to such countries: Azerbaijan (Baku), Armenia (Yerevan), Kyrgyzstan (Bishkek), Moldova (Chisinau), Tajikistan (Dushanbe), Turkmenistan (Ashgabat), Uzbekistan (Tashkent), Lithuania (Vilnius), Latvia (Riga ), Estonia (Tallinn), Georgia (Tbilisi).
LLC «Zapadpribor» - a huge selection of measuring equipment for the best value and quality. So you can buy inexpensive devices, we monitor competitors' prices and are always ready to offer a lower price. We only sell quality products at the best prices. On our site you can buy cheaply as the latest innovations and proven equipment from the best manufacturers.
The site includes a special offer «buy at the best price» - if other Internet resources in products presented on our site, the lower price, we will sell it to you even cheaper! Buyers also additional discount for leaving a review or photo of use of our products.
In the price list contains not the whole range of products offered. Prices of goods, not included in the price list can learn to contact the manager. Also, our managers You can get detailed information about how cheap and profitable to buy instrumentation wholesale and retail. Telephone and e-mail for advice on the purchase , delivery or receipt are shown on the description of the goods. We have the most qualified staff, quality equipment and the best price.
LLC «Zapadpribor» - the official manufacturer's dealer test equipment. Our goal - selling high quality goods with best price offer and service to our customers. Our company can not only sell you the necessary instrument, but also offer additional services to its calibration, repair and installation. That you have a pleasant experience when shopping on our site, we have provided special gifts guaranteed to the most popular products.
Plant «META» - is the most reliable manufacturer of equipment for inspection. Brake stand STM produced on this plant.
Manufacturer TM «Infrakar» - a manufacturer of multifunction devices gas analyzer and smoke meter.
If there is no site in the descriptive information you need on the device you can always turn to us for help. Our qualified managers will update for you on the technical characteristics of the device from its technical documentation: user manual, certificate, form, operating instructions, diagram. If necessary, we will take a photo of your device, or a device stand.
You can leave feedback on the unit purchased from us, the meter, the device, indicator, or product. Your review for your approval will be published on the site without contact information.
Description of the instruments taken from the technical documentation or technical literature. Most pictures of products made directly by our experts prior to shipment of goods. In the description of the device provided the main technical characteristics of the instrument: nominal measuring range, accuracy class, scale, supply voltage, size (size), weight. If the site you see the discrepancy device name (model) specifications, photo or documents attached - let us know - you will get a useful gift with-selling device.
While the need to clarify the overall weight and size or the size of the individual meter you can in our service center. If you need our engineers will help you choose the most complete analog or a suitable replacement for the device you are interested. All counterparts and replacement will be tested in one of our laboratories with the full compliance to your requirements.
Our company carries out repairs and maintenance of measuring equipment in more than 75 different factories of the former Soviet Union and CIS. We also provide such metrological procedure: calibration, tare, graduated, testing of measuring instruments.
If you can make repairs to the device yourself, our engineers can provide you with a complete set of necessary technical documentation: circuit diagram TO, ER, FD, PS. We also have an extensive database of technical and metrological documents: technical specifications (TS), the terms of reference (TOR), GOST (DSTU), the industry standard (OST) test procedure, the method of certification, verification scheme for more than 3,500 types of measuring equipment from the manufacturer this equipment. From the site you can download all the necessary software (the software driver) is required for the product purchased.
We also have a library of legal documents that are related to our field of activity: the law, code, ordinance, decree, temporary position.
Upon request, each measuring device is provided metrological certification or verification. Our staff can represent your interests in such organizations as the metrological Rostest (Rosstandart), State Standard, Derzhspozhiv standard (Derzhspozhivstandart), TSLIT, OGMetr.
Sometimes customers can enter our company name wrong - for example, zapadprybor, zapadprylad, zapadprіbor, zapadprilad, zahіdpribor, zahіdprіbor, zahidpribor, zahidprilad, zahidprіbor, zahidprybor, zahidprylad. That's right - Zapadpribor or zahіdprilad.
LLC "Zapadpribor" is the supplier of ammeters, voltmeters, power meters, frequency meters, phase meters, shunts and other devices such manufacturers of measuring equipment, such as: PO " Elektrotochpribor " (M2044, M2051), Omsk, OAO "Instrument-Making Plant "Vibrator" (M1611, Ts1611), St. Petersburg, JSC "Krasnodar ZIP " (E365, E377, E378), LLC " ZIP Partner" (Ts301 , Ts302 , Ts300) and "ZIP" Yurimov"(M381, C33), Krasnodar, OAO "VZEP" ("Vitebsk factory of electrical appliances") (E8030, E8021), Vitebsk, OAO "Electropribor" (M42300, M42301, M42303, M42304, M42305, M42306), Cheboksary, JSC "Elektroizmeritel" (Ts4342, Ts4352, Ts4353 ) Zhitomir, PJSC "Uman factory "Megger" (F4102, F4103, F4104, M4100), Uman.
© 2005 - 2017 LLC "Zapadpribor".
All rights reserved.