Equipment for maintenance checkup >> - the list of equipment for vehicle inspection >> equipment for inspection and auto service of the plant "GARO" >> brake testers STS

Brake tester STS-4-SP-14 + 2 500$ in GIFT (devices for state technical checkup).

1 340 000 RUB

1 piece

Online prices include VAT.

It is possible effectively delivery of any quantity.
5 000$ as a gift to  brake stands STS. $ 5 000
as a gift for
brake stand STS
    The action "Brake stand STS by factory price + set of equipment for inspection for free" !

    You had discount more than 10% from cost of brake stand. Your savings are to 315 500 RUB. (complete set of equipment for inspection), depending on the selected stand STS.

    Valid time and the number of gift sets are limited.

    More details available here...
or contact our sales department by phone:
    (495) 374-54-18.


Brake stand STS-4-SP-14 complex is movable, which consists of a rack, floor support device and the power cabinet.

     Also this Brake Tester can be called: STS4SP14, STS4SP-14, STS-4SP14, STS-4SP-14, STS 4 SP 14.


    The stand is designed to monitor the efficiency of the service and parking brake systems, as well as stability under braking of cars, vans and small lorries, including all-wheel drive, axle load for travel up to 3 tons.


    The diameter of the wheels (on the bus) - from 520 mm to 790 mm.


    The inner / outer ends of the rollers - 800/2800 mm.


    Measuring force exerted on the control of brake system - from 100 N to 1000 N.
    Meter braking force (for one wheel) - 0-10 kN.
    The initial braking speed on the stand STS-4-SP-14 - 4.4 km / h
    Length of trestle - 11 m
    Power supply voltage - 380 V.
    Power frequency - 50 Hz.
    The installed capacity of electric - 8 kW.
    The range of measurement of weight - up to 3000 kg.
    The maximum power measured maximum brake force for 10 - 20 kW.
    Operating temperature range - from +5 ° C to +35 ° C.
    Roll stand Br CTC-4-SP-14 works by the forced rotation of the wheel axis of the vehicle diagnosed with track rollers and measuring the forces that occur on the surface during braking. After checking out videos on the axis of the support device of weighing the same diagnosed axis. The effort that applies the brake control, vymeryat special sensor. Calculation of total specific brake force and the coefficient of axial non-uniformity of the software is held, which receives data on the weight of the axle and the braking force of each wheel.
    The use when checking the brake system of the classical arrangements of rollers helps reduce errors and eliminate the rollback of the vehicle.
    Rollers stands STS-4-SP-14 is equipped with a metal spot welding SmG, which provides a factor of adhesion of 0.8 on a dry surface and 0.7 - the wet. The diameter of the rollers allows you to stand on the brake wheel contact patch, which will be identical to the wheel contact patch with the road.
    Tester capable of testing all-wheel drive (Module 4 WD - reversing rollers).
    Overpass is for arrival and exit the car on the support rollers, it is mounted on both sides of the platform to set the reference device.
    The control system stand nd CTC-4-SP-14 allows for self-diagnosis. If there is an emergency situation, the system goes into the "error" and the scoreboard shows an error code. The code is determined by the fault.
    The stand is controlled via the remote control or keypad handheld komp'yutera.

    Supplied brake testers STS-4-SP-14

    The support device - 1 pc.
    Overpass - 1 pc.
    Wardrobe power - 1 pc.
    Weighing System - 1 pc.
    Module 4 WD - 1 pc.
    Remote Control Set - 1 pc.
    The force sensor on the control TC - 1 pc.
    Instrument rack SP-6 - 1 pc.
    The bridge - 2 pcs.
    Chock - 2 pcs.
    Set the PC - Optional consumer.
    Tool set for checking the stand - Optional consumer.
    Brake stands STS-4-SP-14 after passing through the initial calibration can be taken into operation with the provision of the warranty is 12 months from the first day of admission to operation.
    The requirements and application instructions contain technical documentation that comes with the stand. Also, the product provides all the necessary certificates.
    Installation, commissioning and training are carried out under a separate contract and are not included in the cost of equipment.

Photos: STS-4-SP-14

STS-4-SP-14 brake tester.
STS-4-SP-14 brake tester.
STS-4-SP-14 brake stand supplied.
STS-4-SP-14 brake stand supplied.
STS-4-SP-14 roller brake tester design.
STS-4-SP-14 roller brake tester design.
STS-4-SP-14 brake stand placement in the operative position.
STS-4-SP-14 brake stand placement in the operative position.