Equipment for maintenance checkup >> - the list of equipment for vehicle inspection >> equipment for inspection and auto service of the plant "GARO" >> brake testers STS
Brake stand STS-4-SP-11 is designed to monitor the efficiency of the service and parking brake systems, as well as stability under braking cars vans and mini trucks, including all-wheel drive, axle load to travel up to 3 tons.
Also this Brake Tester can be called: STS4SP11, STS 4 SP 11, STS-11-4SP, STS4SP-11, STS-4SP11, ctc4cp11, ctc 4 cp 11, ctc-4-cp-11.
Wheel diameter (bus) from 520 mm to 790 mm.
The inner / outer ends of the roller brake tester - STS-4-SP-11 800/2200 mm.
Managing complex - with a reception management.
View the supporting device - with frame weighing device.
Option to install a support device - on a base plate.
Location of the main parts of the stand, STS-4-SP-11
Specifications brake testers STS-4-SP-11
The initial braking speed on the stand - 4.4 km / h
Measuring range force generated on the control of brake system - N. 100-1000
Measuring range of braking force (one wheel) - 0-10 kN.
Power supply - 3x380 V, 50 Hz.
The installed capacity of electric - 8 kW.
The maximum power measured maximum brake force for 10 - 20 kW.
GCW - 0-3000 lbs.
Operating temperature range - from +5 ° C to +35 ° C.
Width wheels - 800/2200 mm.
Diameter wheels of the car - 520-790 mm.
Brake stand STS-4-SP-11 has dimensions:
- A reference device - 2332h700h300 mm;
- Front controls - 625h665h1130 mm.
Total weight - 600 kg.
Tester works on the principle of forced rotation of the wheel axis of the vehicle diagnosed with track rollers and measuring the forces that occur on the surface during braking. After checking out videos on the axis of the support device of weighing the same diagnosed axis. The effort that applies the brake control, vymeryat special sensor. Calculation of total specific brake force and the coefficient of axial non-uniformity of the software is held, which receives data on the weight of the axle and the braking force of each wheel.
Foundation plan of the stand STS-4-SP-11
Rollers stand STS-4-SP-11 coated metal spot welding SmG (Sooth Grip), thereby ensuring the value of the coefficient of friction 0,8-0,7 (dry. / Humidity.).
Objectivity is implemented measurements obtained through the correct size diameter rollers. Roller diameter is selected and calculated in such a way that the tire contact patch, located on the brake stand, was identical to the contact patch with the road. Due to the classical scheme of arrangement of rollers reduces the error in the measurement of the braking force.
Different versions of the coating rollers:
Supplied brake testers STS-4-SP-11
Frame foundation - 1 piece.
The support device - 1 piece.
Wardrobe power - 1 piece.
Weighing System - 1 piece.
Module 4 WD - 1 piece.
Remote Control Set - 1 piece.
The force sensor on the control TC - 1 piece.
Instrument rack SP-6 - 1 piece.
The bridge - 2 pcs.;
Chock - 2 pcs.;
Set the PC - Optional consumer;
Tool set for checking the stand - Optional consumer.
Brake stands STS-4-SP-11 are equipped with high-quality and durable items.
The base frame of the stand is the foundation, which serves to fasten it to the vehicle mounting power racks, tensioners and other devices that allow the hydraulic body changes.
On a foundation built ramyustanavlivayutsya support devices STS-4-SP-11 with the necessary installation components.
The drive and control board STS-4-SP-11
The scheme of connection control board STS-4-SP-11
Electronic control board STS-4-SP-11
The features and technical advantages of the STS stands Brake-4-SP-11
1. Measurement mode automatic.
2. Self-diagnostic system.
3. The possibility of diagnosing wheel drive vehicles (together with the module 4WD, with spot welding rollers SmG, the module auto-lock clips).
4. The ability to measure parameters such as response time, braking system resistance force unbraked wheels, specific brake force; ellipse wheel brake drums, brake force coefficient of uneven wheels on one axle, the relative difference between the axis of the wheel brake forces.
5. The soft launch of rollers.
6. Having software.
7. Installing the roller flush with the floor.
8. The lack of power floorstanding cabinet.
9. Stands CTC-4-SP-11 Direct Transfer diagnostic results to a PC.
10. Having the ability to print the diagnostic results.
11. Ability to resupply technical control.
12. The presence of dynamic weighing.
13. Possibility to control measurements with a PC or remote control.
14. Reduced noise.
15. The possibility of interchanging the base frame with the STS-3-SP-11.
16. The presence of fixing rollers for easy exit the vehicle from the stand.
17. The possibility of completion shall stand tester suspension and withdrawal tester.
18. The possibility of completion shall stand devices for inspection.
For long-term operation of stands STS-4-SP-11, as well as excellent build quality and appearance of the stands they have to meet the following requirements:
- All parts and components must be secured without distortions, durable;
- Threaded connections must be secured against loosening and no damage;
- On the inscriptions on the panels should not be sagging paint, broken lines and no visible difference in thickness;
- Electroplating and coatings must be durable, smooth, with no scratches or cracks.
Stands brake STS-4-SP-11 after passing through the initial calibration can be taken into operation with the provision of the warranty is 12 months from the first day of admission to operation, but no later than 15 months from the date of sale.
The warranty period may be extended by another 12 months in the case of a contract for service products.
The requirements and application instructions contain technical documentation that comes with the stand. Also, the product provides all the necessary certificates.
Installation, commissioning and training of staff on the stand, STS-4-SP-11 are performed under a separate contract and are not included in the cost of equipment.
Photos for tester STS-4-SP-11