Equipment for maintenance checkup >> - the list of equipment for vehicle inspection >> equipment for inspection and auto service of the plant "GARO" >> brake testers STS

Brake tester STS-10U-SP-11 + 5 000$ in GIFT (devices for state technical checkup).

1 085 000 RUB

available:
2 pieces

Online prices include VAT.

For order is possible effectively delivery of any quantity.

technical documentation brake testers STS-10U-SP-11:

STS-10U-SP-11 manual installation.

Download

[doc, 1.1MB]
STS-10U-SP-11 instruction manual.

Download

[doc, 4.9MB]
STS-10U-SP-11 passport.

Download

[doc, 1.3MB]
    Brake stand STS-10U-SP-11 is designed to monitor the efficiency of the service and parking brake systems and stability under braking PBX with an axle load of 10 tons.

$ 10 000
as a gift for
brake stand STS
    The action "Brake stand STS by factory price + set of equipment for inspection for free" !

    You had discount more than 15% from cost of brake stand. Your savings are to 318 200 RUB. (complete set of equipment for inspection), depending on the selected stand STS.

    Valid time and the number of gift sets are limited.

    More details available here...
or contact our sales department by phone:
    (495) 374-54-18.

    Also this Brake Tester can be called: STS10USP11, STS 10U JV 11, STS-10USP11, 10USP STS-11, USP 11 STS10, ctc-10y-cp-11, ctc10ycp11, ctc 10y cp 11.

   
Specifications brake testers STS-10U-SP-11

Parameter name
In the diagnosis of ATC
Range
permissible
relative error,%
passenger
Truck
The initial braking speed, simulated on the bench, not less
4.4 km / h
2.2 km / h
 
Meter braking force (for one wheel)
1.6 kN
3-30 kN
± 3%
Measuring force exerted on the control of brake system
300 - 1000 H
± 4%
Range measuring the weight of each weighting device kg
100-1000 kg
500-5000 kg
± 3%
Measuring range air pressure in the pneumatic actuator, MPa
 
0.2-1 MPa
± 3%
Powered by a three-phase alternating current:
- Voltage,
- Frequency, Hz
380
50 Hz
± 10%
± 1%

    Wheel diameter (bus) 520 to 1300 mm.
    Axles to 10.
    The inner / outer ends of the roller brake tester STS-10U-SP-11 800/2800 mm.

    Rollers stand STS-10U-SP-11 have a metal spot surfacing SmG (Sooth Grip), and provide traction coefficient 0,8-0,7 (dry. / Humidity.).

   
Supplied brake testers STS-10U-SP-11

    Frame foundation - 2 pcs. (Left, right.)
    The support device - 2 pcs. (Left, right.)    
    Wardrobe power - 1pc.;
    Weighing System 1 piece.
    Module 4 WD - 1pc.;
    Remote Control Set - 1pc.;
    The force sensor on the control TC - pedometer -1 piece.
    Electronic metering sensor braking pressure -1 piece.
    Instrument rack SP-6 - 1 piece.
    The bridge - 2 pcs.;
    Chock - 2 pcs.
 
    Optional with STS-10U-SP-11 are available:

    Set a personal computer;
    Calibration Kit;
    Tester withdrawal from rectilinear motion;
    Hydraulic Tester backlash;
    Pressure Tester backlash;
    Gidroimitator load on the axle of the vehicle.
    Brake stands STS-10U-SP-11 are equipped with high-quality and durable items.

    Strain gauge sensors provide highly accurate mass measurements of the vehicle.

    Motor unit brake tester.

    There are also a series of one-piece stands STS. Two pairs of gear motor located in the center of the roller unit.

    Transfer of force from the motor to the drum roller provides a powerful steel chain.

    Manufacturing roller brake tester STS-10U-SP-11osuschestvlyaetsya with welding on steel, which provides a constant coefficient of friction with wear spots. Force meter, which is located on the control of the service braking system, coupled to the processor brake tester, and as a result the measurement results are displayed on the display screen. The stand is equipped with a dynamic weighing system.

   
Different versions of the coating rollers:

STS-10U-SP-11 brake stand different coverage options rollers.

    Brake stands STS-10U-SP-11 are used for testing cars, trucks, buses and trucks. Possible options for operating the stand in a trucking companies, technical control centers and service stations, if the electrical network is not connected to the networks of residential houses.
    Stand STS-10U-SP-11 is as follows. First, measure the axle load is measured braking force at each wheel, the control force and the air pressure in the pneumatic or air-hydraulic brake actuator motor vehicles. Design parameters such as: specific braking force, the relative difference between the axis of the wheels brake force or the vehicle are determined in accordance with GOST R 51709-2001. Calculation of other parameters such as total surface brake force, brake system reaction time, the ratio of compatibility train links, the coefficient of uneven braking forces wheels on one axle, asynchronous response time train brake actuator units determined in accordance with GOST 25478-91.

    The plan of the foundation brake tester STS-10U-SP-11.
STS-10U-SP-11 tester foundation plan.

    Work bench STS-10U-SP-11 is controlled by a PC keyboard and a remote control. Output of control is provided by the printer. Also, it is possible to stand out independent car forward in the direction of motion.

    Dimensions stands STS-10U-SP-11:
    - A reference device - 1235h700h602 mm;
    - Front controls - 625h665h1130 mm;
    - A case of force - 600h210h1000 mm;
    - Instrument cabinet - 600h210h1000 mm;
    - Slip tester - 1000h800h70 mm.
    Brake stand STS-10U-SP-11 has a lot of common - 1220 kg.
    Mode of operation of the stand - Intermittent:
    - UO work - no more than 2 minutes;
    - Pause UO - at least 8 minutes.

    The installed capacity of electric equipment - not more than 15 kW.
    The maximum power consumption of the network in the measurement of the maximum braking power for 10 seconds - no more than 45 kW.
    Warm-up time stand STS-10U-SP-11 - no more than 15 minutes.
    Continuous operation of the stand - at least 8 hours.
    Average life of the stand - at least 8 years.
    While checking ATS lock brake system (stop) the cam follower roller turns off the drive roller bearing device stand.

   
Brake stands STS-10U-SP-11 has an accuracy of response time measurement equal to the accuracy of rounding (display) - ± 0,01 s, which is structurally supported, that is not subject to verification in the course of an acceptance test in the future. Influences the accuracy of the other components is negligible, which is confirmed by the following design parameters of the stand:
    - Technical characteristics of the meter clock, whose stability is provided by a quartz resonator frequency of 7.3728 MHz, designed for long-term frequency stability of better than ± 10 -6;
    - Rounding (display) the results - up to 0.01 sec.
    Equipment stand STS-10U-SP-11 in the working position.

STS-10U-SP-11 tester equipment in position.

    Installing the roller brake tester flush with the floor. Unfolds in a heated hangar. Footprint in the unfolded state 4750h18700 mm at lengths of a pit 12 meters

   
The features and technical advantages of the brake tester STS-10U-SP-11 in comparison with domestic counterparts:

    1. Having two modes initial braking speed.
    2. High bandwidth.
    3. It stands STS-10U-SP-11 does not have a limit on the number of repetitions of the measurement of various parameters and the number of diagnosed axes ATS.
    4. Rollers can be supplied in two forms:
    - Corundum coated (high coefficient of friction, for studless tires);
    - With improved wear resistance due to steel welding on the square of a calibrated (for all types of tires), which provides a constant coefficient of friction with wear rollers;
    5. The presence of STS-10U-SP-11 sensor to measure the air pressure in the pneumatic or air-hydraulic brake actuator motor vehicles.
    6. The possibility of expanding the functions of brake testers, such as the inclusion of the brake tester additional options.
    7. Ability to diagnose all types of PBX, including exchanges with four-wheel drive.
    8. Brake stands STS-10U-SP-11 have the opportunity to install the backup electronic monitor for easy diagnosis trucks.
    9. The software package has the functions of stands:
    - Output of control results to the printer as a diagnostic card and protocol approved pattern of defects found;
    - Ability to export data on the passage TRP and email.
    10. Application in the STS-10U-SP-11 reliable electrical products and ready-made electronic components.
    11. Completeness of the equipment that comes with the stand, can be formed on the basis of individual needs.
    12. The basic set of equipment that comes with the stand, according to the principle of modularity, can be retrofitted to the technical control LTK-10UP-SP-11.
    Stands STS-10U-SP-11 after passing through the initial calibration can be taken into operation with the provision of the warranty is 12 months from the first day of admission to operation, but no later than 15 months from the date of sale.
    The warranty period may be extended by another 12 months in the case of a contract for service products.
    The requirements and application instructions contain technical documentation that comes with the stand. Also, the product provides all the necessary certificates.
    Installation, commissioning and training of staff on the stand, STS-10U-SP-11 are performed under a separate contract and are not included in the cost of equipment.

Photos for tester STS-10U-SP-11

STS-10U-SP-11 brake tester.
STS-10U-SP-11 brake tester.
STS-10U-SP-11 brake tester gauges.
STS-10U-SP-11 brake tester gauges.
STS-10U-SP-11 brake tester motor unit.
STS-10U-SP-11 brake tester motor unit.
STS-10U-SP-11 brake tester piece series STS stands.
STS-10U-SP-11 brake tester piece series STS stands.
STS-10U-SP-11 brake tester strong steel chain.
STS-10U-SP-11 brake tester strong steel chain.
STS-10U-SP-11 brake tester different coverage options rollers.
STS-10U-SP-11 brake tester different coverage options rollers.
STS-10U-SP-11 brake tester foundation plan.
STS-10U-SP-11 brake tester foundation plan.
STS-10U-SP-11 brake tester equipment in position.
STS-10U-SP-11 brake tester equipment in position.
STS-10U-SP-11 brake tester layout production area inspection station.
STS-10U-SP-11 brake tester layout production area inspection station.
STS-10U-SP-11 brake tester layout production area inspection station.
STS-10U-SP-11 brake tester layout production area inspection station.
STS-10U-SP-11 brake tester.
STS-10U-SP-11 brake tester.
STS-10U-SP-11 brake tester usage examples.
STS-10U-SP-11 brake tester usage examples.
STS-10U-SP-11 brake tester usage examples.
STS-10U-SP-11 brake tester usage examples.
STS-10U-SP-11 brake tester usage examples.
STS-10U-SP-11 brake tester usage examples.
STS-10U-SP-11 brake tester usage examples.
STS-10U-SP-11 brake tester usage examples.
STS-10U-SP-11 brake tester usage examples.
STS-10U-SP-11 brake tester usage examples.

Photos of using tester STS-10U-SP-11

STS-10U-SP-11 brake tester usage examples.
STS-10U-SP-11 brake tester usage examples.
STS-10U-SP-11 brake tester usage examples.
STS-10U-SP-11 brake tester usage examples.
STS-10U-SP-11 brake tester usage examples.
STS-10U-SP-11 brake tester usage examples.
STS-10U-SP-11 brake tester usage examples.
STS-10U-SP-11 brake tester usage examples.
STS-10U-SP-11 brake tester usage examples.
STS-10U-SP-11 brake tester usage examples.
STS-10U-SP-11 brake tester usage examples.
STS-10U-SP-11 brake tester usage examples.


Яндекс цитирования