Products catalog

belongings to the selective voltmeters SMV

3/7 TGL 25602 RFT разъем высокочастотный предназначен для соединения и разъединения в электронных цепях передачи сигнала высокой частоты с согласованием.

Соединитель совместим с типом кабелей KAW 5.

More info ...

3/7-St TypIII GOST13317-80 RFT соединитель предназначен для соединения коаксиального кабеля с оборудованием и для соединения двух коаксиальных кабелей друг с другом.

Волновое сопротивление - 50 Ом.

Сечение канала - 7/3,04 мм.

More info ...

AD 13

AD 13 adapter is used to connect the power cable to the jacks calibration object "radio source" on NNB 12.
Plug the cables:
- Conductor cross-section - 4 mm2;
- Maximum insulation diameter - 5.2 mm.

More info ...

AD-11 адаптер представляет собой модифицированный высокочастотный штекерный разъём, к которому подключаются с компенсацией растяжения отдельные жилы кабеля с помощью кабельного наконечника на каждую жилу.

Адаптеры AD-11 служат для подключения кабеля к селективным микровольтметрам типа SMV.

More info ...

AK 101 junction box in conjunction with four probes type TK 102 measures the voltage noise on the individual wires four-wire network.
Frequency range - from 0.15 MHz to 30 MHz.

More info ...

AK 11 junction box is a 4-fold switch measuring sites.
Frequency range - from 0 to 30 MHz.

More info ...

ANB 101

ANB 101 dummy is used to measure voltage noise impinging on radio receivers, network of wires, antenna and ground.
Frequency range - from 0.15 MHz to 30 MHz.

More info ...

ANB 11

ANB 11 equivalent antenna is used to measure the radiation interference radios.
Frequency range - from 0,01 MHz to 30 MHz (composed of FMA 11).

More info ...

AP 1

AP 1 connecting board provides a fast connection to the source of interference terminal strip.
Connections:
- High-wire connection with double shielding type LE 56 (Z - 50 Ohm).
- High-frequency cable connector series 7/16.

More info ...

ATR 2

ATR 2 the bearing construction of the antenna used to komplektatsyy antennas for measurements the intensity fields for test kits type FSM 8.
Diapazon frequencies - from 26 MHz to 1000 MHz.

More info ...

BS 101

BS 101 notch filter is designed to improve immunity in receivers and is a converter for selective microvoltmeter type SMV 6,5.
Frequency range - from 95 kHz to 1000 kHz.

More info ...

BZ 11

BZ 11 consol the battery is part of the additional devices to selectively microvoltmeter type SMV 11.

More info ...

DGF 10

DGF 10 attenuator is used to measure the input power up to 5 W at 50 Ohm with a selective microvoltmeter SMV 11.
Frequency range - from 0 MHz to 30 MHz.

More info ...

DGF 9

DGF 9 attenuator is used to connect to a selective type microvoltmeter SMV 8,5 to extend the measuring range.
Frequency range - from 0 MHz to 1000 MHz.

More info ...

ES 11-1

no-image

ES 11-1 set of parts - contains a set of modules for selective microvoltmeter type SMV 11.

More info ...

FE 1

FE 1 block lifts complete with dipole type DP 1 and antenna support structure of ATR 2 is used to measure the field strength of the measuring set-type FSM 8 and provides continuous height adjustment and antenna polarization.
Frequency range FE 1 in conjunction with ATR 2 - 30 MHz to 300 MHz.

More info ...

FE 2

    FE 2 lifts block complete with a dipole type DP 1 or DP 3 and the supporting structure of the antenna type ATR 2 is used to measure the field strength for measuring kit type FSM 8 and provides continuous height adjustment and antenna polarization.
Frequency range FE 2 in conjunction with the ATR 2 - 30 MHz to 1000 MHz.
More info ...

FE 3

FE 3 block lifts complete with dipole type DP-1, the log-periodic antenna type LPA 1 and antenna support structure of ATR 2 is used to measure the field strength of the measuring set-type FSM 8 and provides continuous height adjustment and antenna polarization.
Frequency range FE 3 in conjunction with the ATR 2 - 30 MHz to 1000 MHz.

More info ...

FERNBEDIENUNG к FE 2 управление дистанционное предназначено для дальностного регулирования блоков лифтов.

Режимы переключения:

- влево и вправо;

- вверх и вниз.

More info ...

FSA 101 антенна ферритовая входит в состав измерительного комплекта BSM 301.

Диапазон частот - от 0,15 МГц до 30 МГц.

Пропускная способность без усилителя - не менее 9 кГц.

More info ...

GB boxes RFT

no-image

GB instrument boxes are harmless for transportation equipment with accessories even when the mechano-dynamical loads.
Types of instrument boxes: GB 11, GB 12, GB 14, GB 15-1, GB 16, GB 18.

More info ...

GG-1 противовес электрический предназначен для получения ёмкости между землёй и некоторой точкой антенны.

Противовесы GG-1 применяются с антеннами серии FMA.

More info ...

HANDWINDE к FE 1, FE 3 лебедка ручная канатная однобарабанная предназначена для подъёма груза по вертикали и для перемещения груза по горизонтали.

More info ...

Kabelhalter держатель кабеля предназначен для крепления кабеля. Держатели Kabelhalter применяются в составе блока лифтов FE 2.

More info ...

KAW 5 сопротивление нагрузочное коаксиальное предназначено для передачи энергии от антенны к приемному устройству, или же от передающего устройства к антенне.

Номинальное полное сопротивление - 50 Ом.

Коэффициент отражения - не более 0,1.

More info ...

KBA 101 батарея входит в состав измерительный комплекта BSM 301.

Напряжение - 12 В.

More info ...

KTG 5

KTG 5 coaxial transforming component serves to match the input impedance of selective microvoltmeter type SMV 8,5, as well as compounds with a weak reflection of any two devices.

Frequency range - from 0 MHz to 1000 MHz.

More info ...

LE 115 кабель предназначен для цепей управления, контроля и информации в разнообразных неподвижных и подвижных установках при переменном или при постоянном напряжении.

Тип кабеля - управляющий; семиполюсный.

Гнездо штекера - 7×25.

More info ...

LE 117 кабель присоединительный состоит из нескольких изолированных друг от друга проводников (жил) заключённых в оболочку и предназначен для присоединения к сети.

Номинальный ток - 4×25 А.

Номинальное напряжение - 380 В.

More info ...

LE 143 кабель присоединительный состоит из нескольких изолированных друг от друга проводников (жил) заключённых в оболочку и предназначен для присоединения к сети.

Номинальный ток - 2×10 А.

Номинальное напряжение - 380 В.

More info ...
no-image

LE 56 кабель соединительный высокочастотный с двойной экранировкой предназначен для соединения эквивалента сети NNB 103 с присоединительной платой AP 1.

Номинальное сопротивление - 50 Ом.

Высокочастотный кабельный штекер - 7/16.

More info ...

LE 61 кабель состоит из нескольких изолированных друг от друга проводников (жил) заключённых в оболочку.

Количество разъёмов - 2.

Количество контактов в разъёме - 9.

More info ...
no-image

LE 69 кабель соединительный предназначен для передачи высокочастотных сигналов между двумя измерительными приборами или другим оборудованием.

Кабели LE 69 применяются для проведения измерений, калибровки и поверки радиоизмерительных приборов разных типов.

More info ...

MOTORWINDE к FE 2 лебедка с электродвигательным приводом предназначена для подъёма груза по вертикали и для перемещения груза по горизонтали.

Напряжение - 220 В.

Частота - 50 Гц.

More info ...

PA 101 антенна пеленгационная предназначается для измерения напряженности электрического поля.

Диапазон рабочих частот - от 26 МГц до 300 МГц.

Волновое сопротивление выхода антенны - 75 Ом.

More info ...

SS 11-1

no-image

SS 11-1 service kit is a set of accessories for replacement, and as a consequence improve the work of the selective microvoltmeter type of SMV 11.
The composition of the service kit:
- 1 adapter card 87 pole;
- 1 adapter card 58 pole;
- 1 bandpass cable 26 pole;
- 1 bandpass cable 15 pin;
- 6 HF connection cables with angled plugs 1/3, 3;
- 1 HF transition part 1/3, 3-BNC 50-by 1;
- 1 puller boards;
- 1 wrench.

More info ...

ST 11 тренога - передвижное опорное устройство предназначено для установки измерительных антенн.

Тренога ST 11 используется вместе с антенной FMA11 для измерения напряжённости поля с помощью селективного микровольтметра SMV11.

More info ...

STA 101 штыревая антенна входит в состав измерительного комплекта BSM 301.

Частотный диапазон - 0,15 МГц до 30 МГц.

More info ...

TG 11

TG 11 transformative component - adapter for matching symmetrical lines with 600 Ohm 50 Ohm coaxial input selective microvoltmeter type SMV 11.
Frequency range - from 10 kHz to 150 kHz.

More info ...

TGL 200-3819 RFT кабель соединительный коаксиальный с контактами высокого напряжения предназначен для передачи низкочастотных сигналов между двумя измерительными приборами или другим оборудованием.

Серия - 7/25.

Емкость - не более 6 пФ.

Диаметр кабеля - 5±0,5 мм; 6±0,5 мм; 7±0,5 мм.

More info ...

TGL 200-3819 розетка высокочастотная коаксиальная водонепроницаемая предназначена для соединения и разъединения в электронных цепях передачи сигнала высокой частоты с согласованием.

Серия - 7/25.

More info ...

TGL 25180 RFT кабель соединительный коаксиальный предназначен для передачи высокочастотных сигналов между двумя измерительными приборами или другим оборудованием.

Серия - 1,6/9,7.

Полное сопротивление - 75 Ом.

More info ...

TGL 25180 штекер высокочастотный коаксиальный предназначен для соединения и разъединения в электронных цепях передачи сигнала высокой частоты с согласованием.

Серия - 1,6/9,7.

Полное сопротивление - 75±0,5 Ом.

Предельная частота - 1 ГГц.

More info ...

TGL 31428 RFT кабель микрофонный предназначен для подключения ленточных микрофонов с высокой чувствительностью.

Серия - 5/21.

Тип выхода - 063-02:00 (FD 51).

Тип соединительного штекера - 063-01:00 (51 KS).

 

More info ...

TK 101 probe in combination with selective Microvoltmeter SMV 6,5 or STV 301-2 measures the high voltage radio interference.
Frequency range - from 0,15 MHz to 30 MHz.

More info ...

TK 102 probe is used to measure voltage interference on the lines.
Frequency range - from 0,15 MHz to 30 MHz.

More info ...

TK 103 probe in combination with selective Microvoltmeter SMV 6,5 or STV 301-2 measures the high voltage radio interference.
Frequency range - from 0,15 MHz to 30 MHz.

More info ...

TK 104 probes in combination with a selective microvoltmeter (SMV 8 and SMV 8,5) provide a high-frequency high-voltage measurement.
Frequency Range - 26 MHz to 1000 MHz.

More info ...

TK 11 probe used for low resistance measurement asymmetrical interference voltages at high current lines.
Frequency range - from 0,15 MHz to 30 MHz.

More info ...

TK 111 пробник используется в сочетании с селективным микровольтметром типа SMV 11 или SMV 8,5.

Частотный диапазон - от 0,15 МГц до 30 МГц.

More info ...

TK 12 probe is used where desirable smaller load measurement object.
Execution - 2,5 Ohm.

More info ...

TK 14 probe is used to measure asymmetrical interference voltages at high current networks.
Frequency range - from 0,15 MHz to 30 MHz.

More info ...

TK 15 probe is part of the measuring kits of FMA 11, which are designed for selective measurement component of the field strength and field strength of radio interference.
Execution - 10 kOhm.

More info ...

ZS 11

ZS 11 accessory set included in the measurement kits of FSM 11.
Depending on the layout of measuring kits, accessories sets are compared in accordance with it, divided into ZS 11-1 (transformative and transforming coaxial link, RF adapters, RF connecting cable, adapter cable) and ZS 11-5 (attenuator and voltage probe) .

More info ...

By type of instrument SMV, NNB and their accessories are presented cables types LE and ÜK battery, battery-connecting, RF instrumentation, RF connector, coaxial, transition, connecting, networking, connecting to the object under test, control types, and other accessories: termination resistor, RF adapter.

More info ...

Coaxial cable LE 37 connection to the SMV, RFT (Germany) is designed to transmit high-frequency signals between the two measuring devices or other equipment. Also used for measurement, calibration and testing of various types of radio devices.

More info ...

Платы ремонтные используются в качестве комплектующих для различных измерительных приборов.

Только у нас Вы найдете более 100 различных типов плат для ремонта и комплектации приборов.

More info ...

Leading online store Zapadpribor - a huge selection of measuring equipment for the best value and quality. So you can buy inexpensive devices, we monitor competitors' prices and are always ready to offer a lower price. We only sell quality products at the best prices. On our site you can buy cheaply as the latest innovations and proven equipment from the best manufacturers.

The site includes a special offer «buy at the best price» - if other Internet resources (bulletin board, forum or announcement of another online service) in products presented on our site, the lower price, we will sell it to you even cheaper! Buyers also additional discount for leaving a review or photo of use of our products.

In the price list contains not the whole range of products offered. Prices of goods, not included in the price list can learn to contact the manager. Also, our managers You can get detailed information about how cheap and profitable to buy instrumentation wholesale and retail. Telephone and e-mail for advice on the purchase , delivery or receipt are shown on the description of the goods. We have the most qualified staff, quality equipment and the best price.

 

Online store Zapadpribor - the official manufacturer's dealer test equipment. Our goal - selling high quality goods with best price offer and service to our customers. Our store can not only sell you the necessary instrument, but also offer additional services to its calibration, repair and installation. That you have a pleasant experience when shopping on our site, we have provided special gifts guaranteed to the most popular products.

 

We offer fast international shipping to almost every country in the world: Australia, Austria, Azerbaijan, Albania, Algeria, Anguilla, Angola, Antigua and Barbuda, Argentina, Aruba,  Bahamas, Bangladesh, Barbados, Bahrain, Belize, Belgium, Benin, Bermuda, Bulgaria, Bolivia, Bonaire, Sint-E. and Saba, Bosnia and Herzegovina, Botswana, Brazil, British Virgin Islands, Brunei Darussalam, Burkina Faso, Burundi, Bhutan, VietNam, Vanuatu, Vatican City, Venezuela, Armenia, Gabon, Guyana, Haiti, Gamia, Gambia, Ghana, Guatemala, Guinea, Gibraltar, Honduras, Hong Kong, Grenada, Greenland, Greece, Georgia, Denmark, Democratic Republic of the Congo, Jersey, Djibouti, Dominica, Dominican Republic, Ecuador, Eswatine, Estonia, Ethiopia, Egypt, Zambia, Zimbabwe, Jordan Indonesia, Ireland, Iceland, Spain, Italy, Cape Verde, Kazakhstan, Cayman Islands, Cambodia, Cameroon, Canada, Qatar, Kenya, Kyrgyzstan, China, Cyprus, Kiribati, Colombia, Comoros, Congo, Korea (Rep.), Costa Rica, Kot-d'Ivoire, Cuba, Kuwait, Curacao, Laos, Latvia, Lesotho, Lithuania, Liberia, Lebanon, Libya, Liechtenstein, Luxembourg, Myanmar, Mauritius, Mauritania, Madagascar, Macao, Malawi, Malaysia, Mali, Maldives, Malta, Morocco, Mexico, Mozambique, Moldova, Monaco, Monaco, Namibia, Nauru, Nepal, Niger, Nigeria, Netherlands, Germany, New Zealand, New Caledonia, Norway, UAE, Oman, Cook Islands, Pakistan, Palestine, Panama, Papua New Guinea, Paraguay, Peru, South Africa, Poland, Portugal, Republic of Chad, Rwanda, Romania, El Salvador, Samoa, San Marino, Saudi Arabia, Swaziland, Seychelles, Senegal, Saint Vincent and the Grenadines, Saint Kitts and Nevis, Saint Lucia, Serbia, Singapore, Sint Maarten, Slovakia, Slovenia, Solomon Islands, United Kingdom of Great Britain and Northern Ireland, Sudan, Suriname, East Timor (Timor-Leste), USA, Sierra Leone, Tajikistan, Taiwan, Thailand, Tanzania (United Republic of), Togo, Tonga, Trinidad and Tobago, Tuvalu, Tunisia, Turkey, Turkmenistan, Uganda, Hungary, Uzbekistan, Uruguay, Faroe Islands, Fiji, Philippines, Finland, France, French Polynesia, Croatia, Central African Republic, Czech Republic, Chile, Montenegro, Switzerland, Sweden, Sri Lanka, Jamaica, Japan.

We also provide such metrological procedure: calibration, tare, graduated, testing of measuring instruments.

The online store takes an active part in such procedures as electronic bidding, tender, auction.

If there is no site in the descriptive information you need on the device you can always turn to us for help. Our qualified managers will update for you on the technical characteristics of the device from its technical documentation: user manual, certificate, form, operating instructions, diagram. If necessary, we will take a photo of your device, or a device stand. You can leave feedback on the unit purchased from us, the meter, the device, indicator, or product. Your review for your approval will be published on the site without contact information.

 

Description of the instruments taken from the technical documentation or technical literature. Most pictures of products made directly by our experts prior to shipment of goods. In the description of the device provided the main technical characteristics of the instrument: nominal measuring range, accuracy class, scale, supply voltage, size (size), weight. If the site you see the discrepancy device name (model) specifications, photo or documents attached - let us know - you will get a useful gift with-selling device.

 

While the need to clarify the overall weight and size or the size of the individual meter you can in our service center. If you need our engineers will help you choose the most complete analog or a suitable replacement for the device you are interested. All counterparts and replacement will be tested in one of our laboratories with the full compliance to your requirements.

In the technical documentation for each device or product, information is provided on the list and amount of precious metals content. The documentation gives the exact weight in grams of precious metals: Au gold, palladium Pd, platinum Pt, silver Ag, tantalum Ta and other platinum group metals (PGM) per unit item. These precious metals are found in nature in very limited quantities and therefore have such a high price.

On our website you can familiarize yourself with the technical characteristics of devices and obtain information on the content of precious metals in devices and radio components manufactured in the USSR. We draw your attention to the fact that often the actual content of precious metals differs by 10-25% from the reference one in a smaller direction! The price of precious metals will depend on their value and mass in grams.

All text and graphic information on the site is informative. The color, shade, material, geometric dimensions, weight, content, delivery set and other parameters of the goods presented on the site may vary depending on the batch of production and year of manufacture. Check with the sales department for more information.

 

If you can make repairs to the device yourself, our engineers can provide you with a complete set of necessary technical documentation: circuit diagram TO, ER, FD, PS. We also have an extensive database of technical and metrological documents: technical specifications (TS), the terms of reference (TOR), GOST (DSTU), the industry standard (OST) test procedure, the method of certification, verification scheme for more than 3,500 types of measuring equipment from the manufacturer this equipment. From the site you can download all the necessary software (the software driver) is required for the product purchased.

We carries out repairs and maintenance of measuring equipment in more than 75 different factories of the former Soviet Union and CIS.

We also have a library of legal documents that are related to our field of activity: the law, code, ordinance, decree, temporary position.