Equipment for maintenance checkup >> - the list of equipment for vehicle inspection >> equipment for inspection and auto service of the plant "GARO" >> brake testers STS
Stationary universal tester BDE 3504 N SC PC 13t SmG (Cartec, Italy) is used to monitor the effectiveness of the service and parking brake systems of cars and trucks, buses and trucks with axle loads up to 13 tons.
Also this Brake Tester can be called: BDE3504 NSC PC 13t SmG, BDE-3504 NSC PC 13t SmG, BDE-3504-N-SC-PC-13t SmG, BDE 3504 NSC-PC13t SmG, BDE 3504-N-SC PC-13t- SmG, BDE 3504 N SC PC 13T SMG.
Diameter wheels of the car - 520-1300 mm.
Track width - 800/2800 mm.
With the brake tester BDE 3504 N SC PC 13t SmG measured:
- Axle load;
- The braking force at each wheel;
- The control force;
- Air pressure in the pneumatic-hydraulic brake actuator ATS;
- Specific braking force;
- The relative difference between the axis of the wheels brake force;
- Asynchronous time delay brake actuator units train.
Maximum axle - 13,000 lbs.
Measuring force exerted on the control of brake system - up to 1000 N.
Meter braking force (for one wheel) - 0-30 kN.
Measuring range air to air drive - 0-1 MPa.
The initial braking speed - 2,5 / 5,2 km / h
The coefficient of adhesion with the rollers dry. / Humidity. - 0.9 / 0.5.
Roller diameter - 205 mm.
Length of commercials - 1000 mm.
Power supply voltage - 380 V.
Power frequency - 50 Hz.
Power consumption - 19 kW.
The maximum power measured maximum brake force for 10 - 20 kW.
Motor power - 2x3, 7 kW.
Dimensions - 1190x600x650 mm;
weight - 50 kg.
Dimensions of the stand BDE 3504 N SC PC 13t SmG (each unit) - 1225x700x550 mm.
Motor power - 2x9, 2 kW.
Weight - 2x400 kg.
Operating Temperature - 0 ° C to +70 ° C.
Brake stands BDE 3504 N SC PC 13t SmG:
- Allow testing vehicles with one or more drive axles mode (4WD);
- Process parameters using strain gauges;
- Reliable measurement electronics accurately captures the emerging powers;
- Display the results, and are controlled by a standard PC;
- Rollers are made of stainless steel;
- The mechanical parts are galvanized;
- A color printout of the results of measurements;
- Electric motors are protected from moisture;
- The ability to add to the diagnosis line.
Additional option - the different modes of tests for cars and trucks, their speed over a range of measurements of weight and braking forces. The bench can be beefed slip tester SSP-4000.
Scope of supply:
1. Block steel rollers for conventional and studded tires (cover SmG) - 2 pcs.
2. Communication cabinet with electrical and electronic components - 1 pc.
3. Power and communication cables - 1 set.
4. Strain gauge load cell - 1 pc.
5. The control system based on the PC - 1 pc.
6. Base frame for supporting devices stand BDE 3504 N SC PC 13t SmG - 2 pcs.
7. Cable to connect the PC and the communication closet - 1 pc.
8. The weighing system of axle load - 8 sensors.
9. Module 4WD. Reverse rolls all-wheel. You must have the remote control and the sensor for measuring the force on the brake pedal PD7 - 1 pc.
10. Infrared remote control - 1 pc.
11. PD 7 - sensor for measuring the force on the brake pedal - 1 set.
12. Air Pressure Sensor LD 5 - 1 piece.
Photos: BDE 3504 N SC PC 13t SmG